Welcome to our websites!
News
-
What are the use methods and maintenance points of the cutting press machine?
1. Use method of the cutting press machine: Preliminary preparation: first of all, check whether all the parts of the cutting machine are in good condition, without loosening phenomenon. Check whether the power cord is firmly connected and determine whether the power supply is normal. At the same...Read more -
How to solve the problem of low speed crawling of hydraulic cylinder of cutting press machine?
1. The hydraulic cylinder of the oil pressure cutting machine has a rod cavity and no gas at low speed, which can achieve the purpose of exhaust by repeatedly running the hydraulic cylinder. If necessary, the two chambers of the hydraulic cylinder can set the exhaust device when the hydraulic sys...Read more -
Safety operation procedure for precision four column cutting press machine
1. Objective: In order to better maintain the equipment and the safe use, to ensure the safe operation of the precision four-column cutting machine. 2. Scope of application: precision four-column cutting machine and other hydraulic cutting machine. 3. Safe operation procedure: 1. The operator of ...Read more -
Operating procedures for the cutting press machine
1. Objective In order to better use the cutting machine, let the cutting machine play its due cutting function, and create more value. 2. Scope of application: hydraulic cutting machine 3. Service regulations 1. The operator of the cutting machine should conduct corresponding training, and must b...Read more -
Why does the clicking cutting press machine leak oil?
There are several reasons for oil leakage: 1. Take a look at the service life of the machine. If it exceeds 2 years, consider the aging sealing ring and replace the sealing ring. 2. When the machine is used for no more than 1 year, the oil leakage on the machine head is because the travel adjustm...Read more -
How to maintain the cutting press machine and extend the service life?
Cupping machine is a mechanical equipment commonly used for cutting materials such as paper, cardboard, cloth and plastic film. In the normal use process, if we can regularly maintain and maintain the cutting machine, not only can extend the service life of the cutting machine, but also can impro...Read more -
How to improve the working efficiency of the cutting press machine
Optimizing workflow: Optimizing workflow is an important aspect to improve the working efficiency of the cutting machine. The layout of production line can be replanned to smooth the logistics between cutting machine and other equipment, reduce the time and cost of material handling; arrange proc...Read more -
What are the normal daily maintenance steps of the cutting press machine?
Clean the cutter surface: First, use a soft cloth or brush to clean the cutter surface. Remove dust, debris, etc., to ensure that the machine appearance is clean and tidy. Check the cutter: see if the cutter is damaged or blunt. If a damaged or blunt cutting knife is found, replace it in time. At...Read more -
How to install the pull rod of the hydraulic plane cutter?
1. First, the upper beam of the hydraulic plane cutter machine is set flat 2, then screw the pull rod up to ensure that the teeth on both sides are as long 3. Then adjust the big nut in the middle to ensure that the hole of the big shaft and the hole of the pull rod are concentric 4. Just knock t...Read more -
What are the use methods and precautions of the fully automatic cutting press machine?
Automatic cutting machine is a kind of efficient cutting equipment, commonly used in textile, leather, plastic and other industries. The use of fully automatic cutting machine needs to pay attention to the following aspects: 1, safe operation. When using the fully automatic cutting machine, it sh...Read more -
What are the hazards of the density deviation of the fully automatic die cutting press machine?
1. Reduction of product quality: the density deviation of the automatic cutting machine will lead to the uneven density of the cut products, too dense or too loose in some areas, resulting in the decline of product quality. For example, for the textile industry, if the density of the fabric is no...Read more -
What should I pay attention to in the conventional operation of the cutting press machine?
During the startup every day, let the machine run for two minutes. When stopping for more than one day, please relax the setting handle to prevent damage to related parts. The knife die shall be placed in the middle of the cutting surface. Wash the machine once a day before leaving work, and keep...Read more